Pica-Marker 2020 Pica-Powder Deep Hole Spray Marker

The Pica-Marker 2020 Pica-Powder Deep Hole Spray Marker makes fast, contactless marking possible where standard tips can’t reach. Built around a refillable, zero-gas pump mechanism, it delivers a quick burst of fluorescent green, chalk-based powder through drill holes up to 250 mm (25 cm) deep and as small as 3 mm in diameter. The 360° rotatable spray arm lets installers mark overhead, vertical, or awkward angles without moving fixtures or pulling hardware. With effective dust and moisture protection, the tool performs on dry, damp, smooth, or rough surfaces—ideal for layout during wood framing, electrical rough-in, plumbing penetrations, and general construction.

Each fill provides up to 1,500 shots, minimizing downtime on site and reducing consumable waste. The powder creates a precise dot or full-surface imprint of the hole, so crews can transfer anchor points, align brackets, or verify drilling locations with accuracy. Because it’s chalk-based, markings can be removed from smooth surfaces when the job is complete, helping protect finished materials while keeping layout visible during cutting, drilling, and fastening.

Pica-Marker Pica-Powder Deep Hole Spray At a Glance

• Deep hole reach (250 mm): Marks cleanly through long pilot holes and sleeves.
• Contactless marking: Powder burst transfers position without touching the surface.
• High shot capacity (≈1,500/ fill): Fewer refills for longer runs and repetitive layouts.
• 360° rotatable spray arm: Access hard-to-reach spots at any angle.
• Zero Gas pump mechanism: No propellants; easy to refill and environmentally mindful.
• Fluorescent green chalk: High-contrast dots that show on bright or dark materials.
• All-surface performance: Adheres to dry, wet, rough, or smooth surfaces; wipes from smooth panels.
• Dust/moisture protection: Designed for dependable operation on active jobsites.

Markets

• Carpentry & Framing: Transfer anchor points and bracket locations through deep pilot holes.
• Electrical & Low-Voltage: Mark panel, box, and conduit positions without removing fixtures.
• Plumbing & HVAC: Locate pipe straps, hangers, and penetrations through insulation or sleeves.
• Masonry & Concrete: Spot exact anchor locations through templates into brick or block.
• Metal Fabrication & Install: Align rails and hardware through pre-drilled metal.
• Facility Maintenance & Municipal: Fast, precise layout in overhead and constrained spaces.
• Trade Schools & Training Labs: Demonstrates safe, accurate deep-hole marking techniques.

When holes are deep or access is limited, pencils and markers struggle to leave a reliable reference. The Pica 2020 solves that with a controlled powder burst that prints the hole location on first try. Crews can set anchors, align brackets, or position fixtures without removing the part or guessing at the centerline. The 360° spray arm lets technicians mark above their heads or around obstructions, and the long-reach tube works through sleeves up to 250 mm deep. Because each fill yields around 1,500 shots, teams spend more time installing and less time refilling.

For contractors, that means quicker layout, fewer mistakes, and less rework. Service techs can make contactless marks on finished panels and wipe them from smooth surfaces when done. In training shops, students learn a repeatable method for accurate transfer marking that carries from wood framing to electrical, plumbing, and metalwork.

Pica-Marker 2020 Pica-Powder Deep Hole Spray Marker Features

• Deep Hole Spray Tube (250 mm): Reaches through long drill holes to leave a precise dot.
• Fluorescent Green Chalk Powder: High visibility for alignment and anchor placement.
• Refillable Zero-Gas Pump: Durable, propellant-free mechanism for long-term use.
• Up to 1,500 Shots/Fill: High capacity for repetitive layout tasks.
• 360° Rotatable Nozzle: Marks at any orientation in tight or overhead spaces.
• All-Condition Adhesion: Works on dry, damp, rough, and smooth surfaces; removable from smooth substrates.
• Dust & Moisture Protection: Helps keep the mechanism operating in jobsite conditions.
• Time-Saving Operation: Quick handling for faster transfer marking and reduced rework.

Pica-Marker 2020 Pica-Powder Deep Hole Spray Marker Includes

• (1) Pica-Powder Deep Hole Spray Marker — Art. No. 2020, refillable body with 360° spray arm
• (1) Long-Reach Tube — Up to 250 mm reach
• Note: Powder refills sold separately

Pica-Marker 2020 Pica-Powder Deep Hole Spray Marker Specifications

• Article Number: 2020
• Marking Method: Fluorescent green, chalk-based powder burst (contactless)
• Reach/Depth: Up to 250 mm (25 cm)
• Compatible Hole Sizes: From 3 mm (≈3–15+ mm typical)
• Capacity per Fill: Up to ~1,500 shots
• Nozzle: 360° rotatable spray arm
• Refillability: Yes; compatible with Pica Powder refills
• Operating Guidance: Effective dust/moisture protection; easy removal from smooth surfaces
• Surfaces: Brick, wood, metal, plastic, tiles, plasterboard, glass, rubber, wet wood, wet rubber
• Propellant: Zero Gas (mechanical pump)

Why Customers Choose the Pica-Marker Pica-Powder Deep Hole Spray Marker

Installers choose this deep hole spray marker when they need precise, contactless marking through long pilot holes without removing the part. The zero-gas pump is refillable and delivers around 1,500 shots per fill, so alignment tasks move quickly on framing, conduit, and bracket work. A fluorescent green chalk dot shows up on rough masonry, painted metal, plastics, and tile, then wipes from smooth surfaces to protect finishes. With a 250 mm reach and a 360° spray arm, crews can mark overhead or around obstacles and hit the exact centerline the first time—reducing rework and keeping installs on schedule.